Cd-technologies RS-1942 L Series NEBS Compliant Racks Manuel d'utilisateur télécharger pdf

LEAD

RETURN

RECYCLE

RS 1942

General: These instructions detail the proper procedure for

installing C&D Technologies' Powercom Division (C&D) NEBS

compliant battery racks. The following describes how to

locate, assemble, and load open-frame racks for C&D

battery mounting applications. Proper attention to these

instructions will help ensure safe, trouble-free performance.

Rack Location: Locate racks in a clean, cool, dry place so

the batteries are not affected by sources of radiant heat,

such as sunlight, heating units, radiators, steam pipes, etc.

Variations of more than 5F (3C) between cells may

cause the battery to float and operate at different voltage

ranges. Top rows of batteries in multiple-tier configurations

tend to operate at slightly higher temperature than those

on lower tiers. Always provide adequate ceiling clearance

for ventilation and maintenance.

Anchoring: To provide stability, safety, and seismic integrity,

racks must be securely anchored to the floor. Anchor bolts

are to be installed per vendor’s specifications and in

accordance with applicable codes. Do not attach rack to

walls without consulting C&D first. Mounting holes are

provided in the base of each frame. All frames must be

secured to floor using all anchor locations. It is the

responsibility of the customer to secure racks in

accordance with allowable floor loading, applicable

codes and regulations.

Grounding: Rack grounding provisions are integrated into

the base of each frame. Two 7/16” (11mm) diameter thru holes

are located at the center of the frame's bottom cross member

and may be used to secure a standard NEMA lug. These

two holes have 1.0” (2.54cm) between centers and have

been masked and are free of powder coating to allow for

electrical contact. Frame to frame grounding integrity is

accomplished via the lower support rail, attached to

each frame with an Internal/External “star” washer.

NOTE:

Floor mounting hardware is to be determined in

accordance with applicable building codes, not by

C&D. For proper certification, a floor anchor must

be a minimum or equivalent to an Hilti HSLM12-25.

CAUTION:

Do not install batteries until the rack has been properly

installed, with all bolts tightened to specified torque and

frames anchored to the floor.

Do not use oil, grease or any other lubricating agent as a

lubricant for cell installation. This could void the warranty.

Lubrication is usually not required due to the low friction

interface of the insulated covers. If necessary, a small

amount of water or unscented talcum powder can be

applied to the rail covers to reduce friction.

FIGURE #1 End view of 2-tier and 2-tier/2-row racks.

D/11

“L” SERIES NEBS COMPLIANT

STANDBY BATTERY RACKS

ASSEMBLY INSTRUCTIONS

RSO1942 2/21/03 2:24 PM Page 1

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - ASSEMBLY INSTRUCTIONS

LEADRETURNRECYCLERS 1942General: These instructions detail the proper procedure forinstalling C&D Technologies' Powercom Division (C&D) N

Page 2

RS 1942TORQUE VALUESHardware Type Torque Value3/8”-16 Bolt, Nut and Lock Washer 15-20 Ft.-lbs (20-27 N•m)1/2”-13 Bolt, Nut and Lock Washer 55-65 Ft.-

Page 3 - FIGURE #3 Placing Frames

FIGURE #3 Placing Frames.FIGURE #4 Installing Cross Braces.FIGURE #5 Installing Back or Center Side Restraint Rails and Covers.FIGURE #6 Installing Su

Page 4

FIGURE #7 Install Bracket Top Rail.FIGURE #8 Bottom Cells Installed.4 Leveling: With all support rails (not all side) rails and covers in place, the r

Page 5 - SAFETY NOTE:

SAFETY NOTE:Take all necessary safety precautions when installing the top row of batteries and rack components, as to not drop anything on the batteri

Page 6 - CONNECTION DETAILS FOR

RS 1942FIGURE #11 Completed Rack Assembly.12 Install Front Cross Braces: Install front cross braces for single row rack and front & rear cross bra

Page 7

DETAIL #1 Brace to Frame Connection.DETAIL #2 Rail to Frame Connection.DETAIL #3 Brace to Brace Connection.Typical Bolted Connections: These typical d

Page 8 - ASSEMBLY

RS 1942C&D technologiesGeneral: These insinstalling C&D NEBdescribes how to loracks for C&D batteattention to these introuble-free perform

Commentaires sur ces manuels

Pas de commentaire

Cd-technologies RS-1942 L Series NEBS Compliant Racks Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Fournisseurs d'énergie Cd-technologies RS-1942 L Series NEBS Compliant Racks. C&D Technologies RS-1942 L Series NEBS Compliant Racks User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Fournisseurs d'énergie Cd-technologies RS-1942 L Series NEBS Compliant Racks