Cd-technologies RS-2098 RDC Rack Manuel d'utilisateur télécharger pdf

STANDBY BATTERY RACK

ASSEMBLY INSTRUCTIONS

APPLIES TO ALL RDC SERIES RACKS

(READ ALL INSTRUCTIONS PRIOR TO INSTALLATION)

Standard and Earthquake-Protected (EP) Racks:

Earthquake-protected racks are similar to standard racks,

with the exception of additional frame bracing, battery restraints,

and cell spacer elements. The battery rack frames are common for

Standard, EP1 and EP2 series for the one-tier, two-tier, three-tier

and two-step racks with the exception of the three-tier EP2 rack.

The frame for the three-tier EP2 rack is unique. RDC-EP racks are

certied to the International Building Code, 2009 edition.

Conguration:

Racks are available in single or multiple tier/step congurations as

shown in Figure 2. Rack components are supplied loose and must

be assembled and secured on-site in accordance with these C&D

assembly instructions, the drawings included with the rack shipment,

and applicable codes.

Rack Location:

Locate racks in a clean, cool, dry place so the batteries are not affected

by sources of radiant heat, such as sunshine, heating units, radiators,

steam pipes, etc. Variations of more than 5 degrees Fahrenheit (3º C)

between cells may cause the battery to become electrically unbalanced.

Top rows of batteries in multiple-tier congurations tend to operate at

slightly higher temperature than those on lower tiers. Always provide

adequate ceiling clearance for ventilation and maintenance.

Anchoring:

To provide stability and safety, racks must be securely anchored

to the oor. Anchor bolts are to be installed per contractor

specications and in accordance with applicable codes. Do not

attach rack to walls without consulting the appropriate structural

engineer. Mounting holes are provided in the base of each frame.

All frames must be secured to oor using all anchor bolt hole

locations.

• Do not install batteries until the rack has been properly

installed, with all bolts tightened to specied torque and

frames anchored to the oor.

• Do not use oil or grease as a lubricant for cell installation.

Lubrication is usually not required due to the low friction

interface of the insulating covers. If necessary, a small

amount of water, unscented talcum or Dow Corning III can

be applied to the rail covers to reduce friction.

CAUTION:

Grounding:

Rack grounding provisions are integrated into the base of each

frame. Two through holes are located at the center of the frame’s

bottom cross member and may be used to secure a standard NEMA

lug. These holes are 0.44” in diameter and 1.0” between centers.

The surfaces surrounding the holes have been masked and are free

of powder coat to allow electrical contact. Frame to frame grounding

integrity is accomplished via the lower support rail, attached to each

frame with internal/external “star” washers.

Two Tier Standard Rack Two Tier EP Rack

Figure 1. Standard Vs. EP Rack

Figure 2. Typical Rack Congurations

RS02098

These instructions detail the proper procedure for installing

C&D Standard and EP (Earthquake Protected) battery racks.

The following describes how to locate, assemble, and load

open-frame battery racks for C&D battery mounting applications.

Proper attention to these instructions will help ensure safe,

trouble-free performance.

Standard vs. EP2 Rack

Two Tier Standard Rack Two Tier EP2 Rack

TYPICAL RACK GROUNDING

PROVISION

2-Step

1 Tier 2-Tier 3-Tier

Std & EP1

3-Tier

EP2

RS02098/0114/CD www.cdtechno.com

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - ASSEMBLY INSTRUCTIONS

STANDBY BATTERY RACK ASSEMBLY INSTRUCTIONSAPPLIES TO ALL RDC SERIES RACKS (READ ALL INSTRUCTIONS PRIOR TO INSTALLATION)Standard and Earthquake-Protec

Page 2 - Brace to Frame

ASSEMBLY INSTRUCTIONS FOR RDC STANDARD AND EP RACKS1. Material Verication: Battery racks are shipped unassembled with a complete set of related draw

Page 3 - Rack Label Placement

5. Installing Support Rail(s): See Figure 5. Place support rail(s) in location using supplied 3/8” bolt, washer, serrated strut nut and nger tighten

Page 4 - Support Rail Installation

ASSEMBLY INSTRUCTIONS FOR RDC STANDARD AND EP RACKS 7. EP Rack Assembly: Install all back restraint rail(s) and cover(s). See Figure 7 and Detail E f

Page 5 - Corner Bracket Reversed

ASSEMBLY INSTRUCTIONS FOR RDC STANDARD AND EP RACKS9. Front Restraint Rail (EP only): With the batteries in place, slide the front side support rail

Page 6 - FIGURE 11

ASSEMBLY INSTRUCTIONS FOR RDC STANDARD AND EP RACKS11. Tie Rod Assembly: Longer EP racks require a tie rod assembly (see rack assembly drawings for d

Page 7 - FIGURE 14

Back to Back Assembly:Where two rows of racks are required, two rack assemblies may be installed back to back.Frame Location: Locate back to back fram

Page 8 - End to End Installation

Any data, descriptions or specications presented herein are subject to revision by C&D Technologies, Inc. without notice. While

Commentaires sur ces manuels

Pas de commentaire

Cd-technologies RS-2098 RDC Rack Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Fournisseurs d'énergie Cd-technologies RS-2098 RDC Rack. C&D Technologies RS-2098 RDC Rack User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Fournisseurs d'énergie Cd-technologies RS-2098 RDC Rack